VT Software to Upgrade eVic-VTC Mini

[Kermit]

(10-24-2015, 01:42 PM)Madboy Wrote:  Kermit

I would like to see in a firmware upgrade on the "Seconds" counter at the bottom of the unit. So instead of seconds i would like 00:00:00 (Hours:Minutes:Seconds).

So the display below should read 00:43:46



Thanks in advance

Madboy

hum, sounds great.

[Kermit]

(10-27-2015, 11:29 AM)djermy Wrote:  hey kermit                                                                                                                                                                                                            iam having trouble getting my mini to update it keeps giving me a system parameter commond fail any ideas

hey, what about now? Did you get it solved by upgrading again?

[Kermit]

(10-29-2015, 08:22 PM)lenivets Wrote:  Suggestion: Support of Stainless steel will be great !
Idea: Calculation of optimal Watt for current resistant.

I got 3 eVic + eGrip is coming.. got yesterday 50m of 0.4 SS wire.. but can't use it
My friend is looking for some Box and comparing now X cube (SS support) and eVic  - guys help me to bring his choice to eVic

that's nice, well, I suppose something great is coming soon.

[Kermit]

(10-30-2015, 02:34 PM)BlackCRX Wrote:  Please use 0.0058-0.006 nickel coefficient for accurate vaping temperature. Currently I have to set it approx 50-100F higher than my other temperature control devices to get the same quality of vape.

I have posted my theory and calculations in the social forum. Thank you.

Thank you.

[BlackCRX]

(10-30-2015, 03:46 PM)Kermit Wrote:  

(10-30-2015, 02:34 PM)BlackCRX Wrote:  Please use 0.0058-0.006 nickel coefficient for accurate vaping temperature. Currently I have to set it approx 50-100F higher than my other temperature control devices to get the same quality of vape.

I have posted my theory and calculations in the social forum. Thank you.

Thank you.

Thank you for reading our suggestion and acknowledging them.

[Madboy]

New Firmware version has been released with Stainless Steel support and a brilliant new screen.

Here is the link for the firmware http://www.joyetech.com/mvr-software/?sid=155

There is also a 1.3 Firmware in the package for SS support and if you dont like the new screen you can just install that.

[Arjan]

Please remove the time and Puff it's totally a waist of screen place.
Puff and time are so unnecessary information for most of the vapers.


But cool SS can be used now

[Madboy]

(11-05-2015, 03:14 PM)Arjan Wrote:  Please remove the time and Puff it's totally a waist of screen place.
Puff and time are so unnecessary information for most of the vapers.


But cool SS can be used now

I actually like the time and puffs as it shows me how long i have been using the coil and how many puffs on that coil. Also i can then reset the counter.

Regards

Madboy

[Arjan]

I tried it but the letters are getting to tiny so I did install 1.3.
Hope that Joyetech will support the old screen set-up in the future

[Smok_King]

(11-05-2015, 03:33 PM)Madboy Wrote:  

(11-05-2015, 03:14 PM)Arjan Wrote:  Please remove the time and Puff it's totally a waist of screen place.
Puff and time are so unnecessary information for most of the vapers.


But cool SS can be used now

I actually like the time and puffs as it shows me how long i have been using the coil and how many puffs on that coil. Also i can then reset the counter.

Regards

Madboy

+1 I use the puff counter to gauge my battery.

---

(11-05-2015, 03:04 PM)Madboy Wrote:  New Firmware version has been released with Stainless Steel support and a brilliant new screen.

Here is the link for the firmware http://www.joyetech.com/mvr-software/?sid=155

There is also a 1.3 Firmware in the package for SS support and if you dont like the new screen you can just install that.

Thanks for the headsup.
You're quicker than Joyetech can announce it.